Maintaining Your New Epoxy Floor: Practical Cleaning and Care Tips
A friendly, practical guide to keeping epoxy and decorative flake floors looking great — how often to sweep and mop, what cleaners and tools to use, how to handle tyre marks, oil and sand, and simple steps to avoid damage in garages and commercial spaces.
Why gentle, regular care pays off
Epoxy and decorative flake floors are chosen because they are durable, low-maintenance and visually striking. Local customers consistently tell us these floors stay looking new for years when they’re cleaned correctly and small issues are addressed early. Regular, simple care preserves the finish, helps prevent permanent staining or abrasion, and keeps work and living spaces presenting well for clients and family alike.
Follow manufacturer and installer instructions first
Every epoxy system has a recommended cure time and care instructions specific to the product and topcoat used. Before you start cleaning, check the paperwork your installer provided or the product label. If in doubt, contact your installer for guidance — your installer can confirm when normal foot and vehicle traffic is safe, which cleaners are compatible, and whether any special topcoat was applied that requires different care.
Routine cleaning: sweep, dust and mop frequency
Keep grit and dust off the floor to prevent scratching. In high-traffic garages or commercial areas, sweep or dust-mop daily; in typical home areas, aim for at least once a week. For deeper cleaning, mop with warm water and a mild, pH-neutral floor cleaner every one to four weeks depending on use. Avoid over-wetting — use a damp mop rather than flooding the surface — and always rinse mop water clean so soil isn’t redistributed.
Safe cleaners and what to avoid
Use mild, pH-neutral detergents or purpose-made epoxy floor cleaners. For grease or tyre marks, a water-based degreaser or a diluted citrus cleaner usually works well; apply, agitate gently with a soft nylon brush, then rinse thoroughly. Avoid harsh acids, concentrated bleach, strong solvents (such as methylene chloride or lacquer thinner), and abrasive powders — these can dull or damage the topcoat. When trying a new product, test it on a small, inconspicuous area first.
Dealing with stubborn marks: tyre scuffs, oil and sand
Tyre scuffs often respond to a soft scrub with a mild degreaser and a nylon brush. For oil or grease spills, blot up excess oil first, then clean with a degreasing solution and warm water. Sand and grit are abrasive — sweep or vacuum them away promptly rather than rubbing them into the finish. For commercial sites with heavy soiling, consider a neutral pH floor cleaner and a mechanical scrubber with soft pads; check compatibility with your floor system before use.
Preventative steps to reduce wear
Simple preventative measures extend the life of your floor: place mats at entryways to capture dirt, use protective pads on chair and furniture legs, avoid dragging heavy or sharp objects across the surface, and choose soft rubber or non-marking casters for trolleys. In garages, keep an eye on chemical leaks and clean spills promptly. Routine visual inspections help you spot wear in high-traffic zones so you can address it early.
When to call a pro and how we can help
If you see areas of wear, peeling, or deep staining, or if you’re unsure which products are safe for your specific finish, contact the installer or a local epoxy specialist for advice. Flaked Floor Coatings serves the Gold Coast, Brisbane and Northern NSW and can advise on compatible cleaners, provide maintenance recommendations, or arrange professional touch-ups and recoats where needed. For personalised guidance or a free quote, reach out to the team at our Ormeau location — they can review your floor in person and recommend the best next steps.
Article by
Flaked Floor Coatings
Flaked Floor Coatings - trusted epoxy flooring specialists serving the Gold Coast, Brisbane, and Northern NSW. With 10+ years experience, we install durable epoxy and decorative flake systems for garages, homes, showrooms, warehouses, and commercial properties. We specialise in floor preparation, honed & polished concrete, non-slip coatings and metallic epoxy finishes. Local, family-owned team delivering long-lasting, low-maintenance floors — call for a free quote and view our project gallery.